Search results

robtl; your welcome, happy to help out! Tech Tip; * the Browning "H" split-taper bushing is interchangeable with the Maska "L" split-taper bushing. * available from your favorite pump or area electric motor supplier. Happy Holidays Greg Thoennes Arimitsu Pumps Sales & Tech. Support

Shaping up to be nice turnout with nearly a full tour bus. 4-5 seats remaining....contact Andrea at the HCA office (515) 224-6845 for registration information. Also visit www.heartlandcarwash.org/road-show.cfm Thank you, Greg Thoennes Arimitsu Pumps

Hi David, ken-pro and phred113 have good suggestions. Check for leaks, worn check valves, and avoid bottoming out a regulator...especially if the regulator is rated to over 2000 psi. When replacing nozzles, be sure correct nozzle size (orifice) is used. Keep in mind; the pump only puts...

BG, Your seals are most likely questionable at best. Most who have been through this would also recommend not re-using them. I have helped new and old timers who have returned washed out Cat heads. Most times they are money ahead, rather than adding cost of sleeves, machining, new seal kit &...

310 manifolds MEP, That sounds good, you should find guard clearance to be OK with changeover to the Arimistu 516. Changeovers to Arimitsu 516 have been a non-issue using existing guards. I measured the guard used by National Pride to be 8-7/8". D&S, Dilling-Harris, Etowah Valley, A-OK...

310 manifolds Hi MEP, The 5CP is 4.25" from the base plate to the center of the shaft, compared to 4.5" on the Arimitsu 516. Operators do their changeovers 1 of 2 ways; A) 516 pump, 30102 rails, & 22mm bushing - existing pulley is re-used. or B) 516 pump shipped mounted on 30102 rails...

310 manifolds Here is a handy formula for folks to determine required horsepower; Multiply Pump GPM X PSI then divide by 1500 examples; 5(gpm) x 1500(psi) / 1500 = 5 hp 4(gpm) x 1500(psi) / 1500 = 4 hp 4.5(gpm) x 1200(psi) / 1500 = 3.6 hp 4(gpm) x 1200(psi) / 1500 = 3.2 hp 3.5(gpm) x...

Thanks RPH, I watched the video from you post about a week ago and yes, amazing. I was watching the History Channel last night and they ran a commercial for a program airing Sun.eve, 1/25 @ 8/7central titled "Extreme Marksman". They show a snip which appears to be the same fellow in your...

Hi Jason, When you say "resealed", did you put new seals in the pump? If not, that would be my next step. Greg Thoennes Sales & Tech.Support Arimitsu Pumps

Hi Jason, What did you find in the 6 pump valves when you removed and cleaned them? (I suspect you meant "valves" and not "plungers" as originally described) It is possible that after you completed your service, more debris entered the pump and became lodged in the valves while your customer...

I thought this was pretty darn neat.... This B-29 model aircraft runs on four chainsaw motors. Click on the site below, http://users.skynet.be/fa926657/files/B29.wmv Greg Thoennes Sales & Tech.Support Arimitsu Pumps

As long as you have the head apart, I would recommend pulling the 6 valves and inspecting the valve seat orings. Especially the inlet valves-these are the 3 facing out the front of the head. This could account for both the piece of rubber that you found and the intermintent pulsing and noise...

Background checks I was at a family get together yesterday for a nephews 2yr birthday party and learned about the Facebook website.....which seems to be popular for many. It was mentioned that a school was informed of evidence, found on Facebook, regarding inappropriate behavior of some...