Search results

I have four new hose units and two lightly used units up for sale. Six total. They did not work out for me at my wash for my customers. Ready to ship via USPS if it fits ship's box. New $40.00 each. Ships to you for $ 180.00.

I had an idea while traveling through Yellowstone seeing bear-proof trash cans all over the place. Why not build some for my self-serve wash. I've had issues with people digging for cans, spreading trash, and pouring out old soda cans all over my floors. It's been 3 weeks since installing these...

I have a 4 bay Wash located in Central Oregon. I do 98% of maintenance and new equipment installs my self. I wish to hire out a new triple foam system due to back issues and can't find any company's in my area. Anyone in Oregon/Washington have any leads? All I've found is one out of Portland and...

I have one bay the reset button is popping. This suddenly just started happening. Can anyone tell me what to look for or why this may be happening? I can reset it then 4-5 hours later it happens again. Thanks

So I'm upgrading my bay wash mat station and need some advice. Installing new mat holders and want to use a fastener that will not get loose or fail over time. What are the best to use in this application? Thanks

So I bought some new mosmatic comfort hoses to try out for my foam brush hoses. Two of the bays have them. I see a big decrease in the amount of foam being delivered in those bays with these hoses as they are a smaller diameter. Anyone else experience this or are you using them just for high...

Went to the wash today and one pump was very noisy. Opened the fill cap and water got inside. The pump is running fine other than that. The new one won't be here until next week. Can I keep it in service??? Just don't know how they fail and if it will cause other issues. Thanks

I'm looking to upgrade all my older Doyle vacuum coin acceptors. I found one on Kleen rite and looking for confirmation on the fitment. https://www.kleen-ritecorp.com/p-61453-microcoin-ql-style-electronic-coin-acceptor.aspx Does anyone know if these will work? Thanks, David

So I have one bay that often has a Tap issue. Tired searching but nothing comes up. The customer will hold the card up to pay and will turn on for 2 seconds and then turn off and say thank you. They then will do a mag swipe and it works normal. Any thoughts? This only seems to happen in one bay.

So mother nature remodeled one of bays and need some advice on options to replace the ceiling. It seems the old vinyl is special order. A contractor suggested marine plywood painted white. What are you guys using for the ceilings in your bays? Any other options to consider? Any input is...

Hello, I'm troubleshooting a 1998 Raypak floor heat unit. I had a guy out and he seems to think it the pump or flow switch. He looked at the Honeywell automatic vent damper and said they don't use those anymore. He suspects that could be bad as well. The contractor has since bailed on me and I'm...

Has anyone experienced their coin value change by itself yet? My coin count was down in 3 out of 4 bays and looked into it and the device setting was changed from $25 cents to $0 cents in 3 bays. I have not been in the settings in months. The problem has been fixed but concerned how this...

This weekend I have an air shutoff valve go bad on my tire system. This valve is 115Volt and turns off and on the air flow to the my flojet. The inlets are 1/4 pipe. Looked on Kleenrite and they seem to out of everything. Anywhere else I can locate one online that you guys know of? Also these...

Good morning, I'm running Dixmor 6 timers in my bays and getting ready to change my start-up price. Do those timers override the ones installed in my control boxes in the equipment room? I upgraded the bay panels a couple of years ago and kept the same startup price so I'm just unsure when I go...

So I wanted to post a small battle I've been dealing with over the past couple of weeks for your humor. My Fragramitics spot shampoo CCD unit stopped making suds. Since I bought the wash 3 years ago it's been working great. I replaced the entire hose assembly 9 months ago just to be sure it was...

This weekend I was at the wash and noticed when the foamy brush was being used on bay 1 a humming sound was coming out of the control box. I narrowed it down to the trickle valve making the sound. I don't know the purpose of this valve and why it does this. The tag says DH 18473, 1/8 orfice, 100...

This morning we pulled up to the wash and the tire cleaner was on and the chemical was pumping out of the gun. The panel was turned off. No one around but the system was on and the flowjet pumping fluid? Any ideas on where I should start troubleshooting? Never seen this problem before? Thanks

I have an older Ray Pak floor heat boiler that's running great but the thermostat has not worked in years. The part number is SP-32 made by Goldline. I found a company that rebuilds them and it was returned still not functioning. Has anyone found a replacement unit that's plug and play? 115V...

I have an older single rear load vending unit that the pull handle locks up when you pull to vend. It seems to click 2-3 times then locks up? What would I look for to fix the problem? I’ve tried two coin mech’s and bench testing works great? I can't seem to find anything on this site or online...

Last year I bought a 4 bay SS with 6 vacuums & vending from my folks which they owned for 18 years. It was in repair and needed a lot work. We took the challenge head on and replaced all 4 bay panels, booms, hoses, guns, Cryptopay readers in all bays, updated vacs with Cryptopay, painted the...