Search results

If you are getting a rotate too long code, one of the rotate proxes is not coming on as quickly as the program is expecting. It goes into an emergency rinse cycle if it's applied presoak to the vehicle but can't complete the wash. That's why you are seeing a rinse to home.

Please call PurClean tech support at 844-627-9274. Select option 8 for tech support, then listen for the water treatment system option to reach an advisor who can assist you.

I would recommend you call in for service. In wash count 4861, you had a code 8112 that happened first and this indicates one of the arm rotate proximity switches is "OFF" for 3 seconds. The code A129 indicates the state of the proxes that are on. "A" indicates the machine is not at home. The...

Please call Ryko technical support at 844-627-9274. Support is option 8, and option 2 is Ryko.

I'd like to get one of the tech advisors to give you a call and work through it with you. If you can PM me your contact info, I can have one of them give you a call if you are on-site

Some assumptions here... Guessing it's a Ryko machine since you listed code 07 and guessing it's a Softgloss machine. If that is correct, when the machine approaches the exit end of the tracks, the front endstop prox (PLC input X7) should turn "ON", then the machine should decelerate slowly...

PM sent.

If your machine has an FX2N or FX3U, please check PLC inputs X17, or anything between X70-X77. If any of those are still "on", you have a circuit protector or current relay tripped.

If your machine has an FX2N or FX3U, please check PLC inputs X17, or anything between X70-X77. If any of those are still "on", you have a circuit protector or current relay tripped.

That's surprising! We haven't done anything with RykoNet 1 in years! We discontinued that back in '09 or so.

I sent you a PM.

I'm sorry, but as this was a 12 year old thread that was specific to a site having some issues, it would probably be better if you sent me a PM describing exactly what model of CAW you have, and what the issue is you are experiencing. Will be happy to try to assist, but this original thread...

If the green light is flashing 3 times every 5 seconds, the PLC node is not communicating to the CAW. Usually this is a connection issue. Make sure you are using Belden 8760 throughout all the cable runs. The shield wires should be tied together, but should only connect to a ground in one...

If you don't have the bayplate, the concept is still similar. As the vehicle is leaving, the gantry photoeye input should come back on, then the backup photoeye input along with 2 pulses of the tire finder photoeye. The inputs will vary depending on the exact model, but there is an I/O chart...

Going forward and back is likely not going to resolve it. I'm going to assume you have a setup using a physical bayplate on the floor and an air hose as the backup air switch. the machine needs to know the vehicle pulled forward and that it has left the bay before that control power will drop...

On a SGMX5, as the machine comes back to the home position and reset occurs, we are looking for the vehicle in the wash to exit. This varies a little depending on what vintage machine you have, and what types of bayplates (physical or phototyes). We are looking for transitions of these as the...

If it's flagging a vehicle left early code, it's likely losing the bayswitch signal for more than a few seconds so it thinks the vehicle has left. It should usually give you a few minutes to get back into position before it would fully reset. I'd recommend you call in on our customer line...

Those keypad timers should be able to power up without anything connected to it. I'd power down that coinbox, disconnect the additional cables except for power, then try powering it up. Next, I'd try to get into programming mode. Press and hold the MODE, and SELECT buttons simultaneously...

If your machine wasn't built to include the hot wax option, it won't have the relays, routing solenoids, etc. to activate it. Just to keep it simple, 2 drying agents and ColorWave. It doesn't matter what drying agents you want to use, but the order of the passes won't change on your machine.

Correct, really your only option would be to replace the Clearcoat with Graphene. You wouldn't be able to add a hot wax option because you are already using the 2 drying agents it has available. Unfortunately, there isn't a lot of flexibility in the program in the older units related to expansion.