Search results

Anything rigid that we mount we take pvc pipe and cut a bunch of 1/2" spacers to put behind anything. Use a holesaw the size of the spacer and now you have something to secure without crushing and costs almost nothing. I never recommend hollow core material in SS bays, its not a matter of if it...

Reach out if you would like to chat? I have done a few rehabs both with new and used equip. Am getting ready to do a 3+1 now in Central Pa. Look me up on Facebook to message, not on the forum much anymore.

Are you by chance doing a double pass on the back of small cars? If so you need to shorten the hose, when the trolley goes back and forth the end of the hose binds against the overhead support bridge, sometimes pushing hose-boom into wall. We get our hoses made locally to the length we want...

Turn both regulators down to ZERO. Turn a bay on and get your liquid flow to what you want for flow rate for product. Than slowly turn air up till you get the foam consistency is where you would like it to be. Be sure your mixes in all 3 tanks are close in consistency, add a little to your delay...

I have one that needs a little work ill sell you cheap.

Running the numbers over and over, time and again. Membership is all about the numbers. I like the membership model, just dont feel it works so much with IBA sites. Works perfectly when you have capacity to handle 2500 or more members, not so much when its only a few hundred members.

MY OPINION< Unlimited memberships programs are awesome! I just cant get the numbers to work in an IBA. IBA's are rarely attended like a tunnel wash. Memberships is all about the numbers. You need to sell to every swingin di*k in your area! If not marketed/sold properly, it wont work! If you only...

I know this is a little bit of an older thread, but reading through this I would think it had to be either a bad tbar eye, amplifier or a connection in that circuit somewhere. If the machine passed the mid limit it then looks at the eyes to clear the vehicle. When that happens it makes its turn...

So are you using the Sensortron frame just to hold the heat strip? If so I'm a little confused as to why you wouldnt just put the heat strip on the faceplate itself? I always try to keep them as close to the middle of the faceplate as possible? I have had Crypto swipers for over 10 years and...

Why not just put a vfd control and a plc together and you can control the speed of the pump/motor for different pressures/functions? I would have cleaned up my wiring in the photo's to be more presentable before posting. But hey if you got something great throw it out there! I have rehabbed...

Paul, You have a local guy in your area that sells methanol. Kelly Racing Fuels. Give him a shout with any needs. He is a great guy, just be sure to have an hour to listen to him! He loves to talk. Rich P. He is also friends with Randy K.

Dover/OPW also purchased PDQ some time ago.

We will usually use a little heat in the winter time. I always use the wood on the end of a bench or stair rail and put the fitting against the wood two hands and my beer gut, spit on it and slam it in there wiggling back and forth a bit. Works pretty well on up to 3/4" stuff. Never had a...

Look and see if you have a Sealmaster distributor or a Neyra distributor in your area. There is a product called solveall that is used by sealcoaters to do some cleanup. It might work along with elbow grease. If it was a water based product and cured? It will be a pita to get off, if it was...

Eugene, I fully understand protecting their distributors. But what about the customers? Washworld is doing the same thing! What happens when there are no "GOOD, DEPENDABLE, HONEST, TRUSTWORTHY" distributors in your area? Unitechs tech support is horrific. go online and make an appointment...

I have radiant tube heaters in both my washes. We put the heater in the equip room and sleeved the tube through the block wall into the bay. The heating units dont last in the bay. With doors and floor heat you might not need additional heat.

Hey Maxwell. looking to see if available? If so a little description of what is available and details?

If you dispense quarters with a Cryptopay or other swiper you are losing $$$$. I have installed Cryptopay swipers on my American changers, but only to dispense tokens. I set it for a $5 swipe for 6-$1 tokens.

Whats up Sooner. If you go to my Facebook page you can see everything at the location. Magictouch Car Wash Levittown I will close the facility down in June, everything will be going.

What ya lookin for? I will have a whole facility in a few months.