What's new

GinSan "The Ultiamte" 3-bay problems

soonermajic

Well-known member
Joined
Oct 26, 2014
Messages
3,384
Reaction score
869
Points
113
Location
texas
My Allen Bradley relay, on bay #2, is chattering to the point of throwing my breaker. Tech came out & changed my GinSan GS-27D, & that fixed it....for 12 days. Now doing the exact same thing again. Any advice...?
 

MEP001

Well-known member
Joined
Aug 30, 2007
Messages
16,665
Reaction score
3,946
Points
113
Location
Texas
Check your incoming voltage - if you get 208 from the city and the equipment has 240v transformers you'll have a low-voltage problem.
 

mac

Well-known member
Joined
Sep 3, 2007
Messages
3,558
Reaction score
791
Points
113
You should also contact the "tech" who did the repair and tell him what happened. Most reliable service companies will warranty a repair for 30 days or so. Hold their feet to the fire. Chattering can be caused by low voltage. It's a little odd that only one does this. If it were a case of low voltage it should make them all do that. What you might try is to just swap the chattering part with another and see if the problem goes with it, or stays with that bay.
 

cwguy.com

The Eric
Joined
Sep 13, 2007
Messages
649
Reaction score
0
Points
16
Location
Birmingham, AL
It's a little odd that only one does this. If it were a case of low voltage it should make them all do that.
I am pretty sure on Ginsan units.... each bay is self contained. Except for the weep. It has been 2 years since I worked on one though! :) Some pictures are via the link below.... the bottom unit is the working unit.
http://cwguy.com/?p=6971
 

Stuart

Member
Joined
May 24, 2008
Messages
255
Reaction score
0
Points
16
Location
Tornado Alley
you might check the wiring from the coinbox through the coinbox switching, back to the ER controls. may have a wire that is coming loose. maybe the switch for motor in coinbox is having problems. fwiw
 

vinh

Member
Joined
Dec 27, 2007
Messages
238
Reaction score
0
Points
16
you might check the wiring from the coinbox through the coinbox switching, back to the ER controls. may have a wire that is coming loose. maybe the switch for motor in coinbox is having problems. fwiw
The above from Stuart is right. Also Check the 24V coming to the Allen Bradley contactor. If it is putting out intermittent 24 V voltage then it can be the Ginsan 27 again. You can also replace the 24V transformer.
 

soonermajic

Well-known member
Joined
Oct 26, 2014
Messages
3,384
Reaction score
869
Points
113
Location
texas
When you say "coinbox", what exactly are you referring to? Also, what do you mean by "coinbox switching...ER controls " ?
 

cwguy.com

The Eric
Joined
Sep 13, 2007
Messages
649
Reaction score
0
Points
16
Location
Birmingham, AL
When you say "coinbox", what exactly are you referring to? Also, what do you mean by "coinbox switching...ER controls " ?
Coinbox: meterbox
Coinbox switching: buttons, switch
ER Controls: where the wires terminate from the meter box

I would pay closer attention to the "Motor Latch" and HP function wires from the meter box to the equipment room.... also through your buttons or switch. You can meter them while on and off to see if the wires and buttons are working correctly.

But since there was actually a tech at his location.... I would assume the tech would check the wires already?
So if that does not help.... try bypassing the GS-27D and seeing if that fixes the problem. Maybe the GS-27D really is breaking the system somehow? Also by bypassing the GS-27D you will be able to tell if the transformer is okay.
 
Last edited:

soonermajic

Well-known member
Joined
Oct 26, 2014
Messages
3,384
Reaction score
869
Points
113
Location
texas
Is the coinbox actually where you put your money, in the bays? Forgive my ignorance, as I just bought this, after coaching 24 yrs.
Buttons , & switch. Where are those? Where you put your quarters, in the bays?
 
Etowah

cwguy.com

The Eric
Joined
Sep 13, 2007
Messages
649
Reaction score
0
Points
16
Location
Birmingham, AL
Is the coinbox actually where you put your money, in the bays? Forgive my ignorance, as I just bought this, after coaching 24 yrs.
Buttons , & switch. Where are those? Where you put your quarters, in the bays?
Yes.... a coin box or meter box is where you put your money. Ginsan likes to use buttons.... but they sell meter boxes with switches instead of them. But your system may not be "pure" ginsan.... (another brand) it really does not matter either way. Everything works the same.... basically.

http://cwguy.com/?p=7198
 

I.B. Washincars

Car Washer Emeritus
Joined
Aug 30, 2007
Messages
4,285
Reaction score
1,165
Points
113
Location
SW Indiana melon fields.
Meter box/coin meter = Out in the bay, where the customer puts their money. Some may call it the coin box, but that is easily confused with the box where the money ends up, which may or may not be right there where the money is inserted.
 

vinh

Member
Joined
Dec 27, 2007
Messages
238
Reaction score
0
Points
16
Yes.... a coin box or meter box is where you put your money. Ginsan likes to use buttons.... but they sell meter boxes with switches instead of them. But your system may not be "pure" ginsan.... (another brand) it really does not matter either way. Everything works the same.... basically.

http://cwguy.com/?p=7198
Eric, good to see you helping people with pictures from my carwash.
 

soonermajic

Well-known member
Joined
Oct 26, 2014
Messages
3,384
Reaction score
869
Points
113
Location
texas
we bypassed GS -27D, & it would fire up & work. Does that mean GS 27-D is bad? That's what I am thinking...
 

vinh

Member
Joined
Dec 27, 2007
Messages
238
Reaction score
0
Points
16
Yes. Switch bad 27d to another bay and see if it happens also. Call Dan in tech support. He very smart.
 
Etowah

cwguy.com

The Eric
Joined
Sep 13, 2007
Messages
649
Reaction score
0
Points
16
Location
Birmingham, AL
we bypassed GS -27D, & it would fire up & work. Does that mean GS 27-D is bad? That's what I am thinking...
The GS-27D does actually do things.... Even though they are not necessary. The functions are basically….. if any LP function is ON no weep in that bay. Low water cuts off all bays and the best feature an one second delay for HP.

So since you just replaced the GS-27D something connecting to the device is causing the issue.

Or the problem will break the GS-27D over and over again.
 

soonermajic

Well-known member
Joined
Oct 26, 2014
Messages
3,384
Reaction score
869
Points
113
Location
texas
cwguy,
that's what I'm thinking......that it must be something else. Common sense is telling me that. We just replaced the GS, & it messed up in 10 days. Also, we seemed to have diagnosed it going bad on bay 3 as well.....frustrating...!!!!
 

cwguy.com

The Eric
Joined
Sep 13, 2007
Messages
649
Reaction score
0
Points
16
Location
Birmingham, AL
I would definitely not put a new GS-27D in that bay either. You have to figure out the problem first.

I would try putting a meter on the terminals of the gs-27 to see if you can figure it out that way.

But if you have the problem in 2 bays.... It has to be the weep or the low water float or the wiring for those. I would think?

My guess would be the low water float. Your water level could even be to low maybe?
 

soonermajic

Well-known member
Joined
Oct 26, 2014
Messages
3,384
Reaction score
869
Points
113
Location
texas
My water level in holding tank seems fine...If that's what you're talking about...?
Man this is frustrating!
 

MEP001

Well-known member
Joined
Aug 30, 2007
Messages
16,665
Reaction score
3,946
Points
113
Location
Texas
Look and see if there's a low water cutoff float switch in your tank - if the water is causing too much agitation it might be bobbing and shutting off the bay.
 
Top