Say, for those of you that have in-bay dryers such as Air Shammes, what has been your experiences with keeping good handles in the bay? At $95 a pop I'm questioning how long the handle will last? I have not purchased the system yet. However, that is my one reservation. I'm wondering if I'll spend more money on those darn handles than I'm making? Of course, many of our customers think the handle belongs on the ground so the next vehicle can run over it!
Air Shamee
- Thread starter Josh Corp
- Start date
OurTown
Well-known member
Our Diskin Air Shammee gun has lasted pretty well but now the trigger gets stuck halfway or all the way. It is hard to tell but I think it has been run over a couple of times. I'm surprised that only a handful of times we have seen it on the ground. Maybe other customers pick it up. We are going to try the Air Logic gun that does not have a trigger. About $3,500 in sales so far (only have one right now) and other than the gun we have literally not done a thing to it. It even has the original hose.
Hi Our Town:
That is good to know. The majority of my customers will pick up the spray wands (or at least not run over them) unlike the vacuum hose nozzles. So I I think most understand that there is value in the wands that is greater than the vacuum wands so it should work out. Thank you for the information. Any other experiences from others?
That is good to know. The majority of my customers will pick up the spray wands (or at least not run over them) unlike the vacuum hose nozzles. So I I think most understand that there is value in the wands that is greater than the vacuum wands so it should work out. Thank you for the information. Any other experiences from others?
Eric H
Well-known member
I switched to the Air Logic nozzle and removed the Diskin pressure relief valve ( not all of their systems have the relief valve). The smaller opening and lack of restriction from the Diskin trigger assembly has improved the performance of the dryers.
OurTown
Well-known member
Where would I look for this?
CarWashBoy
Active member
Having the AIr Dryers available to customers makes up the difference of Any Problems.. Put Dryers in all bays and smile..
you will be happy..
Eric H
Well-known member
Not all of the air shammees have the relief valve. Troy stopped using them after a few years. They were usually located coming out of the motor housing. It is just a 2” molded pipe with a spring and a big diaphragm. When the gun trigger was in the closed position the valve would open to allow any excess air to escape.
mjwalsh
6 bay SS w/laundromat
Not sure if we have the absolute very best possible ... but our customers seem to be OK with the extra simple Carolina Pride wand-gun-nozzle for our specific self service Blo Dry. Could this be another case of "ignorance is bliss" ???
???wyatt
Active member
I have a couple locations that I’ve never replaced a nozzle and one location I’ve replaced 3 in the last two months... one broke and the other two went missing. I even super glue them on so who knows what happened to them.
MEP001
Well-known member
Because of the material the guns and hoses are made of, it's almost impossible to glue them on. Try this tape - you'll have to lubricate it with mineral spirits or denatured alcohol to assemble it, but once that evaporates it'll be stuck.
Scotch 1 in. x 1.33 yds. Permanent Double Sided Extreme Mounting Tape 414-48 - The Home Depot
For your toughest jobs, go for our strongest hold-Scotch-Mount Extreme Double-Sided Mounting Tape with its 3M industrial strength adhesive. Equipped with our powerful permanent adhesive, this double-sided
www.homedepot.com
Earl Weiss
Well-known member
- Joined
- Aug 31, 2007
- Messages
- 6,372
- Reaction score
- 943
- Points
- 113
Replaced first nozzle after 3 years. don't like the cuff they come with so I replace that with a standard cuff. When Nozzle broke I temporarily replaced with standard Vac Claw. Worked great except I was afraid t would fly around if not secured in the holder. Was thinking I could make a half insh hole where you hold it to belled off air to keep it from flying around and customers hand would cover it when using it. I might try that.
MEP, Thanks for the feedback. I'm not familiar with the yellow or orange claws. Can you give me abit more information on these handles / claws?
MEP001
Well-known member
I meant the vacuum nozzles, you mentioned your customers leave them on the ground and they get run over.
Waxman
Super Moderator
The air dryers are great in the bays! They get alot of use and you can't beat the low cost to operate this function. Plus they really do work well. I use them on my car when I wash it; makes towel drying after alot easier and fast.
Thank you for the input.
