Hydrominder suction stub
- Thread starter APW
- Start date
MEP001
Well-known member
Not sure. I went ahead and ordered some of the link you provided. Hopefully it is. Thanks
I believe this is the one your looking for. It has a hose barb but the tips push in. https://www.kleen-ritecorp.com/p-12833-hydro-systems-3401-r-ultra-lean-1-4-in-hose-barb.aspx
Or if you want the suction tub with the screw in tips it takes a 1/2" OD hose and it is https://www.kleen-ritecorp.com/p-21...r-hydrominder-eductor-models-506-and-511.aspx
Or if you want the suction tub with the screw in tips it takes a 1/2" OD hose and it is https://www.kleen-ritecorp.com/p-21...r-hydrominder-eductor-models-506-and-511.aspx
MEP001
Well-known member
He said the tips thread in.
Really, that’s why I put a link to both of them.
I didn’t know you can use DEMA parts on a Hydrominder.
MEP001
Well-known member
Neither one matches what he asked for.
I took a leap and guessed he might have DEMA proportioners or someone used DEMA parts on a Hydrominder. DEMA is the only one I've ever seen with a threaded tip in a 1/4" barb.
MEP001
Well-known member
I use the large screw-in ones, mainly because that's what almost everyone around here has. I hate the push-in ones because they're so hard to get out without destroying them. I've worked on at least 500 different car washes and I've only seen the small screw-in ones a couple times.
Earl Weiss
Well-known member
- Joined
- Aug 31, 2007
- Messages
- 6,363
- Reaction score
- 941
- Points
- 113
I use a lot of Ultra lean small push in tips. Yes, you need a tool to get them out.
Greg Pack
Wash Weenie
I use the hydro 1/4" push in tips. I have a strong preference for the 1/4" chemical line. The 1/4" screw in tips are dema and are also used on hydraflex injectors.
Wanted to let everyone know that the ones in the below link, work. You have to teflon them but other than that they work like a champ. Thanks Mep.
OurTown
Well-known member
Another idea is to use the large Hydro screw in tips, run a 2 1/2" long piece of 1/2" ID tubing and then step it down to 1/4" ID to go to the bucket/drum. What I like about this is the tips are easy to remove because of the square head, you can see what tip you have in there easier and of course the advantages of the 1/4" ID tubing of which there are many.
Greg Pack
Wash Weenie
Just going to update this with some info that this thread provided. A couple of days ago I installed the 90 degree dema barb that mep has listed above from KR on a hydrominder 511. I'm using a hyperconcentrate foaming brush (quest berry blitz 3XC)and it typically requires a dual tip eductor or on site dilution. I got good results by installing the single dema/hydraflex tip. I tried a Burgundy tip and it was a bit too watery, but the lime tip worked well.
Those tip have TINY orifices but I've had no trouble using the micro tips with quest products, but I maintain pretty good chemical hygeine practice. All containers are capped with a hole drilled through for the chemical tubing so it minimizes the possibility of contamination from dirt, etc. I'll see how it works and if I do have issue with clogging I'll try to update.
I'd like to try a versadial on the hydrominder 511 but was told they don't work well with viscous products. If I do I'll let everyone know the results.
View attachment Attachment.mp4
Those tip have TINY orifices but I've had no trouble using the micro tips with quest products, but I maintain pretty good chemical hygeine practice. All containers are capped with a hole drilled through for the chemical tubing so it minimizes the possibility of contamination from dirt, etc. I'll see how it works and if I do have issue with clogging I'll try to update.
I'd like to try a versadial on the hydrominder 511 but was told they don't work well with viscous products. If I do I'll let everyone know the results.
View attachment Attachment.mp4
Last edited:
