John J Spokas
Active member
The old one step at a time approach is best.
WW 1.0 Desperate and need help
- Thread starter Cal-Redwood
- Start date
Cal-Redwood
Member
Thank you for the advise John.
Cal-Redwood
Member
Thank you again Tom, received copies of your schematic today, with these schematics I've more confident to connect those wires back together. Hoping that there won't be many components will be failed. Thank you very much for your help.
Tom Thumb
Active member
check back in with us and let us know how it goes.
Cal-Redwood
Member
Sure will do and thank you
Waxman
Super Moderator
If you can get a good electrician to help you it will be well worth it!!!
Cal-Redwood
Member
Thank you Waxman
Cal-Redwood
Member
Hi all, I have been working on my auto wash with all wires are reconnected and still run into some problems.
The following tests have been perform: Manual switch test on Gantry and walk through all functions are working good.
Did the Screen Test from computer (ECP) with the following errors:
HP Soak, HP Wax, HP Rinse, Med Pressure are partially work, water shooting out good but won’t oscillate.
Note: The Pre Soak, Spot free rinse and Low PH Pre Soak, all 3 of these functions are working good (spray water) and oscillating, only high pressure functions are shooting out water but not oscillating.
I have change both amplifier in Gantry but still not oscillating.
Please help, your ideas and directions are greatly appreciated.
Thank you
The following tests have been perform: Manual switch test on Gantry and walk through all functions are working good.
Did the Screen Test from computer (ECP) with the following errors:
HP Soak, HP Wax, HP Rinse, Med Pressure are partially work, water shooting out good but won’t oscillate.
Note: The Pre Soak, Spot free rinse and Low PH Pre Soak, all 3 of these functions are working good (spray water) and oscillating, only high pressure functions are shooting out water but not oscillating.
I have change both amplifier in Gantry but still not oscillating.
Please help, your ideas and directions are greatly appreciated.
Thank you
Cal-Redwood
Member
I think I might find the problem why it won't oscillate on HP wash, found the HP hose broke loose on one side (customer side) of the oscillator. will find out after I get the new connector.
Cal-Redwood
Member
Still failed with new connector installed.
Tom Thumb
Active member
Check the output card in gantry to check for signal to VDF.
Cal-Redwood
Member
Hi Tom, on VDF(VLT2-Oscillating) to out put card, I have a grey wire go from VDF S1 to output card pin 4 (oscillating motors). On low pressure tests, the Pre Soak, Spot free rinse and Low PH Pre Soak are working correctly with (spray water) and oscillating the output cars pin 4 LED is turn on. When on high pressure tests, the HP Soak, HP Wax, HP Rinse, Med Pressure are partially work, water shooting out good but won’t oscillate, the output card pin 4 LED is off. Don't know why there are no signal to turn on pin 4 LED when it's on high pressure tests. Tom, would you please check on your system on the output card, how many wires on pin 4 output card, on my system there is only one grey wire on output card pin 4. Thank you very much for you help.
Tom Thumb
Active member
The information you are looking will be on the Ele. Schematic for the gantry I sent you.
follow the wires from SRT2-ODO8 too the drive for the oscillating drive.
, they should match the wires on the schematic.
If you want to call me or e-mail i will try to help
Cal-Redwood
Member
Thank you for your help Tom. I will verify the wire connection again and let you know.
Cal-Redwood
Member
Hi all, thank you very much for all your help, my system is now up and running. Thank you again Tom for your detailed information.
