Search results
-
K
Have an old hydrospray system
Which didn’t make much since because the second stack is typically the shorting stack for the motor controls- Kyle1
- Post #72
- Forum: Self Serve
-
K
Have an old hydrospray system
This is the wiring diagram I got from Coleman hanna as well for the switch- Kyle1
- Post #71
- Forum: Self Serve
-
K
Have an old hydrospray system
Yes that wire going into the fuse holder is going to the transformer- Kyle1
- Post #70
- Forum: Self Serve
-
K
Have an old hydrospray system
Then connecting to the motor starter wire- Kyle1
- Post #67
- Forum: Self Serve
-
K
Have an old hydrospray system
This is what I’m trying to figure out- Kyle1
- Post #66
- Forum: Self Serve
-
K
Have an old hydrospray system
Ok so I’m here and the last connector is the motor starter wire and the first one is the 24v hot. I ran the hot to the transformer. Is that correct? And the motor starter wire I still don’t know where to run it I have fuses jumping to the top of the overload- Kyle1
- Post #65
- Forum: Self Serve
-
K
Have an old hydrospray system
So basically connect the motor starter(orange), 24V hot(black), hp soap,wax,rinse, and spot free and the timed hot(red) all together inside the motor room. Then run one wire to the contactor. Which port should I connect it to?- Kyle1
- Post #63
- Forum: Self Serve
-
K
Have an old hydrospray system
This is what I have for the tire cleaner, ps and fb since I’m using Flowjet what do I need to setup the hot, coin pulse wire, motor start and the timed hot wire? @MEP001- Kyle1
- Post #60
- Forum: Self Serve
-
K
Have an old hydrospray system
So would I need relays for the high pressure functions since it requires a motor?- Kyle1
- Post #59
- Forum: Self Serve
-
K
Have an old hydrospray system
So what type of relays and din setup would be best?- Kyle1
- Post #57
- Forum: Self Serve
-
K
Have an old hydrospray system
I also have the relays jumped on the 11 port as well- Kyle1
- Post #55
- Forum: Self Serve
-
K
Have an old hydrospray system
How I have it wired so far: Coming from the bay to the relay: A1+ Relay 1: timer output A1+(R1) timed output red R2:TC sol yellow 3PS 4:hp soap 5: FB 6:rinse 7:HP wax 8:spot free 11: low pressure air solenoid 15: tokens (quarter/card coin pulse 16: coin vac output/coin switch I am now needing...- Kyle1
- Post #54
- Forum: Self Serve
-
K
Have an old hydrospray system
Sorry for the amount of time to reply I have been doing a massive overhaul but I got rotary switches in the bays and now this is where I’m stuck and I’m currently not getting power to the bay- Kyle1
- Post #53
- Forum: Self Serve
-
K
Have an old hydrospray system
With a voltmeter, I have the function pressure on and I check the hot wire with one and I connect it to the nut which gives me a reading of 24 v- Kyle1
- Post #48
- Forum: Self Serve
-
K
Have an old hydrospray system
Well I wasn’t getting any pressure when the soap function was on. But I fixed that However, still no soap to the bays I tried the following 1) poured soap directly into the tank 2) rechecked the solenoids and they are still good 3) checked the voltage at the bay and I am getting the proper...- Kyle1
- Post #46
- Forum: Self Serve
-
K
Have an old hydrospray system
This is what I’m looking at right now- Kyle1
- Post #44
- Forum: Self Serve
-
K
Have an old hydrospray system
@cantbreak80 i bought brand new solenoids and they looked just fine- Kyle1
- Post #43
- Forum: Self Serve
-
K
Have an old hydrospray system
I’m also going to try what @MEP001 suggest and pour chemical directly into the tank- Kyle1
- Post #39
- Forum: Self Serve
