Search results

A lot of sites say "Touchfree Automatic", and "SoftTouch Automatic" on a side by side Thank you for your business, and hope the machine runs well for you!

When you replaced the MAC valve and gauge, did you also replace the regulator for trailing air? If so, it's possible you may not have replaced it with the correct one. Most of the MAC regulators are the standard pressure versions, but for trailing air, it uses a low pressure version, P/N...

If the machine is at the rear and driving towards the front (exit), the rear brushes are controlled by "rear trailing air". If you read the gauge for rear trailing air, it is labelled at 10PSI. On all Ryko rollover machines, the pressure designations in the MAC panels should be considered the...

Depends on how your setup questions are answered, and which application you are doing. Presoak will always be fed from the RO/softwater tank in the pump stand. Valve Y7 in the pump stand feedds the 2HP boost pump and this feeds the appropriate water valve for the chemical being applied. If...

As Waxman said, it could be the boost pump running backward. If it is backwards and run that way for a while, that could also damage the impellor. Is Y7 in the pump stand opening? You could put a screwdriver on top of the coil (while coil is on the valve), so see if you can feel the magnetic...

On the older Rainmaker EnviRO units, we did use the 11219-203 valve. I thought you were talking about the Y7 valve that is the RO/soft water inlet valve that comes off the bottom of the soft/RO holding tank in the pump stand that feeds the 2HP boost pump. Still same concept though. If you...

Q14 is the 5A breaker that supplies the 24VAC hot signal labeled as wire 526 to the PLC that controls PLC outputs Y40 through Y77. If Q14 is tripping when you turn on the presoak test, the three outputs that should be coming on are Y40 (presoak air and water), Y66 for the soft water pump...

In both situations, it depends "when" these happened in the cycle. If they were in the first pass of presoak, the machine is basically using the readings from the ultrasonics to map the vehicle. If it were in one of the subsequent passes, it's more likely mechanical or a prox. In the first...

I would also recommend checking your 24VAC at that point in the wash cycle by monitoring wires 26 and 25. At that point in the wash, the wash water solenoid should be turning off, and the wax/CC water solenoids will be turning on, depending on how your wash package is setup. It's possible you...

If I understand you correctly, the machine does it's pass from front to rear where the brushes close. Machine continues to drive reverse as needed because of the short bay. When the machine starts to drive forward for rinse, the rear arms aren't opening fast enough. Is that correct? The...

Sorry, but can't really speak to "how" something is formulated.

Not sure what you are asking... How is what achieved? Yellow chemical with a blue backlight? It's simply shining through.

Final Shine is yellow, but we are also using a blue LED light behind it for accent, and it looks good. The blue foaming wax would have been one of our standard trifoam waxes, and it does have a carnuba base. That product should foam just as well.

Final Shine is a yellow colored foaming ClearCoat protectant that we use in ColorWave and in foaming arches designed with a polymer to increase the life and shine of the product on the vehicle surface. It's designed to not leave any residual foam on the vehicle, even if present going into the...

The video above is actually our Softgloss MAXX 3. In the following video at 2:17 in, it does show the Softgloss MAXX in our Customer Experience bay using our Final Shine in a ColorWave application and how it rinses. We have several other foaming wax products that should rinse equally well...

How about installing some LED strip lighting on the outside edges of the conveyor rail to illuminate more like a runway light? Should be an easy target for your customers to see and help align properly. Most conveyors have support structures for the top rail that you should be able to strap...

LOL! I hope you do too!!! Thank you for your business, and I hope it works out well for you!

Todd, please reach out to our Marketing team at sales@ryko.com. They should be able to verify if you still have time to get in on the Softgloss fall promotion deal. It is a lot of machine for the money!

As PCI requirements change, processors continue to evolve their software to meet those requirements. Last summer, Authorize.net advised their customers that they were updating their servers to require TLS ver 1.2 to process cards to meet those updated standards. Ryko similarly had to update...

Recommended bay length - 38'. Min recommended is 32'. Recommended bay width - 16'. Min recommended is 14'-6". Recommended bay height is 12'. Min recommended is 11'-4". For the length dimensions, the 38' references an unobstructed bay to allow full machine travel with the arms out. You can...