Search results

Sold my 5/1 today. After seven years of dealing with the great unwashed...I've had enough. The death knell came when two partners built an express 200 YARDS from my wash. It immediately took 25% off my bottom line and eliminated any chance at growth. I worked hard to run a nice place and for...

This will give you some general numbers/percentages and some numbers to use as a bench mark... https://carwashmag.com/wp-content/uploads/ALN_surveys/2021_in_bay_automatic_survey.pdf

Waxman... What chemical line did your distributor set you up with....????

What you might try is using the attached exploded view to replace the orings (item #10 on subassembly B) Oring source attached.... https://www.generalpump.com/wp-content/uploads/2019/05/CWR1003-Regulator.pdf 2.62mm X 13.1mm (NBR) Buna-N 70 Duro Metric O-Ring [N2.62X013.1] : The O-Ring Store...

Hey Mac... Did you get a deposit...? When do you close...,?

I have had this happen as well. The springs in the button are VERY stiff for this application. Replace them with the buttons in the link bellow.....softer springs. Just swap out the micro switchs that you have to the new buttons...

I found the contactor in the control cabinet.....its a seiman part Its tough getting old.....just another brain cramp.

MEP001.... Could you elaborate on the contactor......??? I have an electrician coming tomorrow and I would like to be able to point it out. In other words ...where do I look for it? Thank you.....

Equipment is a Coleman super saver... Went in this morning and found the high pressure gun on in one of my self serve bays and no one in it.....believe it to be fresh water. Had to throw the breaker to get it to stop I do hope I didn't lunch the motor.......overheated for sure. Any help would...

Hey Mac.... Any interested/qualified buyers come your way??? I read in Auto laundry news that the 800 pound gorilla....Mr Car Wash...has purchased the 5 site Express/full service Downtowner chain in your town. Got to be tough to compete with... Good luck with the sale.....

https://www.kleen-ritecorp.com/p-19124-super-swivel-25061-tf-double-bearing-1-in-f-x-f-90-degree-swivel.aspx

I haven't seen this in the thread so i will throw this out there.... I had a similar intermittent problem with the Trolley. It would actually hit the stop and throw the belt. According to a Wash World tech the easiest way to test the trolley gearbox is this... Using the remote.... park the...

Copper globe... after a search....no luck finding a source for the kit you are looking for (General pump #K316) What you might try is using the attached exploded view to replace the orings (item #10 on subassembly B) Oring source attached...

I suggest you add....Pick ups....Fold in side view mirrors. The extended ones they use for trailers will catch the arm.

So....what is the standard gross income multiplier for a car wash ??

I found the listing....good luck with the sale! https://www.coldwellbankerhomes.com/fl/cape-coral/826-cape-coral-parkway-e/pid_42829859/

Thanks Greg.....the tips and tricks where helpful. The replacement was pretty strait forward and if you take your time to check things it was a 30 minute job. Reason for replacement.....lost the relay that sent the signal to the razor for the top wash. I attempted to change relays (recommended...

Has anyone had the need to replace the CPU/motherboard in a WSII? If yes...what are the Gotcha's for both replacement and programming? Thank you...

Thank you Randy! You where dead on.... Unplugged the coin acceptor and Dixmor showed $$$ Replaced the acceptor and the bay is back in business

A little help here... After a heavy rain last night I went into one of my bays to find the screen reading COIN and it stays that way. It will not register a coin drop or a bill. If I unplug it /plug it back in it will flash the dollar amount and then immediately goes to COIN on the...