JE Adams Coin Deposit Air Machine "No Air Pressure"

[Good Moody]

Good day,
Ive had the unit since new approx 7 years and it stopped producing air pressure, I haven't disassembled it yet to seek something obvious mechanically but thought Id ask you all if you've ever experienced this before.
A new motor assy delivery is near $700.00, hoping to not have to spend that much on a low use vending machine.
I appreciate your input!

 

[Randy]

You've probably got a bad air compressor or a control relay. Get out the volt meter and start checking for power.

 

[Good Moody]

You've probably got a bad air compressor or a control relay. Get out the volt meter and start checking for power.

I'm hoping not the motor of course, when I experienced it yesterday it was pushing air but very little.

 

[Earl Weiss]

1 Open Cabinet - Let it run and put finger over tip and listen for air leaks. Also try to disconnect hose at compressor and put finger over outlet to see if you have good pressure. (If pressure is good it will be difficult to impossible to hold finger there. 2. Some compressors have a filter on inlet. Make sure it is clean. 3. Some compressors have a Bleed Off valve allowing compressor to start under zero pressure.. Make sure it is not stuck open, Report back.

 

[Good Moody]

1 Open Cabinet - Let it run and put finger over tip and listen for air leaks. Also try to disconnect hose at compressor and put finger over outlet to see if you have good pressure. (If pressure is good it will be difficult to impossible to hold finger there. 2. Some compressors have a filter on inlet. Make sure it is clean. 3. Some compressors have a Bleed Off valve allowing compressor to start under zero pressure.. Make sure it is not stuck open, Report back.

Yes, I did these steps and it has near no pressure when you cover the hose end with your finger, and I didn't see a air filter. What pressure it has is near nothing.

 

[Earl Weiss]

You can try a compressor from Harbor freight BUT. 1. Make sure it will fit cabinet. 2. Make sure it is "Oilless" 3. You can easily adapt any fittings to fit a 1/4" hose. I don't know how much use your until gets but if you think about it they only run for 4 minutes at a time. Also use an :"Open Chuck" I have had some HF freight units last a long time in my machines. Also check this out . https://www.amazon.com/California-Air-Tools-SP-9421-Compressor/dp/B00NGK47FK/ref=sr_1_19?adgrpid=1330409639921904&dib=eyJ2IjoiMSJ9.lT3rqF9dZcKhAOTWG4EO7AI2uikwr4PoaIcCTF5YpNyXUvYImQymyafNxOMl5y5YzFuyC2oJ9xN_tkWcLrnBCIP-ho7OaAr5JoyvDLVaZt-aUwtCu8llm8-4YvttjA7QEmxMcnaIYoHUo9JXIeCJn6kQ1jX4CXfoZfTFxwk-dJivvKJJePj8mFZ00wPu1wiSnuyRdLElbYpGE1gDSXoviKtUUtsZc2hAt9ja5h75503g2SY0YRYarGcIqajryd0lJgjOwpimGT6Eggdo0gNjaXX2df0SwE5bs5ccCTEEDzU.OMPaqGingLzwKZaahbzwekIf8K6tCzylHi0YwnKNcns&dib_tag=se&hvadid=83150841225139&hvbmt=be&hvdev=c&hvlocint=4084&hvlocphy=103735&hvnetw=o&hvqmt=e&hvtargid=kwd-83150957842725:loc-190&hydadcr=1643_13458088&keywords=california+air+compressors&msclkid=3ebd89d835bb18f7935eefb5b0c8ff6a&qid=1718453632&sr=8-19

 

[Good Moody]

You can try a compressor from Harbor freight BUT. 1. Make sure it will fit cabinet. 2. Make sure it is "Oilless" 3. You can easily adapt any fittings to fit a 1/4" hose. I don't know how much use your until gets but if you think about it they only run for 4 minutes at a time. Also use an :"Open Chuck" I have had some HF freight units last a long time in my machines. Also checkthis out . https://www.amazon.com/California-Air-Tools-SP-9421-Compressor/dp/B00NGK47FK/ref=sr_1_19?adgrpid=1330409639921904&dib=eyJ2IjoiMSJ9.lT3rqF9dZcKhAOTWG4EO7AI2uikwr4PoaIcCTF5YpNyXUvYImQymyafNxOMl5y5YzFuyC2oJ9xN_tkWcLrnBCIP-ho7OaAr5JoyvDLVaZt-aUwtCu8llm8-4YvttjA7QEmxMcnaIYoHUo9JXIeCJn6kQ1jX4CXfoZfTFxwk-dJivvKJJePj8mFZ00wPu1wiSnuyRdLElbYpGE1gDSXoviKtUUtsZc2hAt9ja5h75503g2SY0YRYarGcIqajryd0lJgjOwpimGT6Eggdo0gNjaXX2df0SwE5bs5ccCTEEDzU.OMPaqGingLzwKZaahbzwekIf8K6tCzylHi0YwnKNcns&dib_tag=se&hvadid=83150841225139&hvbmt=be&hvdev=c&hvlocint=4084&hvlocphy=103735&hvnetw=o&hvqmt=e&hvtargid=kwd-83150957842725:loc-190&hydadcr=1643_13458088&keywords=california+air+compressors&msclkid=3ebd89d835bb18f7935eefb5b0c8ff6a&qid=1718453632&sr=8-19

Interesting! Thank you Earl!
I appreciate it.

 

[Good Moody]

You can try a compressor from Harbor freight BUT. 1. Make sure it will fit cabinet. 2. Make sure it is "Oilless" 3. You can easily adapt any fittings to fit a 1/4" hose. I don't know how much use your until gets but if you think about it they only run for 4 minutes at a time. Also use an :"Open Chuck" I have had some HF freight units last a long time in my machines. Also check this out . https://www.amazon.com/California-Air-Tools-SP-9421-Compressor/dp/B00NGK47FK/ref=sr_1_19?adgrpid=1330409639921904&dib=eyJ2IjoiMSJ9.lT3rqF9dZcKhAOTWG4EO7AI2uikwr4PoaIcCTF5YpNyXUvYImQymyafNxOMl5y5YzFuyC2oJ9xN_tkWcLrnBCIP-ho7OaAr5JoyvDLVaZt-aUwtCu8llm8-4YvttjA7QEmxMcnaIYoHUo9JXIeCJn6kQ1jX4CXfoZfTFxwk-dJivvKJJePj8mFZ00wPu1wiSnuyRdLElbYpGE1gDSXoviKtUUtsZc2hAt9ja5h75503g2SY0YRYarGcIqajryd0lJgjOwpimGT6Eggdo0gNjaXX2df0SwE5bs5ccCTEEDzU.OMPaqGingLzwKZaahbzwekIf8K6tCzylHi0YwnKNcns&dib_tag=se&hvadid=83150841225139&hvbmt=be&hvdev=c&hvlocint=4084&hvlocphy=103735&hvnetw=o&hvqmt=e&hvtargid=kwd-83150957842725:loc-190&hydadcr=1643_13458088&keywords=california+air+compressors&msclkid=3ebd89d835bb18f7935eefb5b0c8ff6a&qid=1718453632&sr=8-19

I DONT SEE ONE IN HARBOR FREIGHT ONLINE?

 

[OurTown]

If it's on the side of your building you could run an air line from your ER compressor and add a solenoid valve instead of replacing the expensive onboard compressor.

 

[Speed Wheels]

If the onboard compressor for your building's air line is expensive to replace, an alternative solution could involve using an existing ER compressor. By running an air line from the ER compressor and integrating a solenoid valve, you could efficiently manage the air supply without the need for a costly replacement. This setup allows for controlled air distribution to various points in the building, ensuring reliable operation without significant additional investment. It's essential to ensure compatibility and proper installation to maintain optimal performance and reliability of the air supply system.

 

[Randy]

I DONT SEE ONE IN HARBOR FREIGHT ONLINE?

Harbor Freight has a small Avanti Airbrush Compressor Combo Kit that might fit your needs. They Also have a CENTRAL PNEUMATIC 1/5 HP 58 PSI Oil-Free Airbrush Compressor Kit.

 

[Good Moody]

If it's on the side of your building you could run an air line from your ER compressor and add a solenoid valve instead of replacing the expensive onboard compressor.

It sits to itself on a Vac Island

 

[OurTown]

It sits to itself on a Vac Island

Bummer. I figured it would be a long shot.

 

[Earl Weiss]

I DONT SEE ONE IN HARBOR FREIGHT ONLINE?

I used something like this. Just took compressor off the tank. If I recall correctly there were some goofy size fittings I had to adapt. https://www.harborfreight.com/8-gallon-15-hp-150-psi-oil-free-portable-air-compressor-64294.html

 

[Good Moody]

I used something like this. Just took compressor off the tank. If I recall correctly there were some goofy size fittings I had to adapt. https://www.harborfreight.com/8-gallon-15-hp-150-psi-oil-free-portable-air-compressor-64294.html

INTERESTING, REALLY?, YOU DIDN'T USE THIS SPECIFIC COMPRESSOR?, HOW LONG HAVE IS IT BEEN IN PLAY EARL?

 

[Earl Weiss]

INTERESTING, REALLY?, YOU DIDN'T USE THIS SPECIFIC COMPRESSOR?, HOW LONG HAVE IS IT BEEN IN PLAY EARL?

I had Thomas and Gast that lasted for 10 years or more. Been using the harbor freight unit for several years. I do recall it was a PITA to try to adapt the fitting that wasn't typical 1/4"

 

[Good Moody]

I had Thomas and Gast that lasted for 10 years or more. Been using the harbor freight unit for several years. I do recall it was a PITA to try to adapt the fitting that wasn't typical 1/4"

Ok, Guess that's what I'll replace it with!
Thank very much for the insight Earl.

 

[Earl Weiss]

Use an "Open Chuck" makes startup easier on compressor.

 

[Good Moody]

Makes sense.