Search results

Be sure to check the flow rate. If you have 4 ss bays that can use 3.5 gpm you will need a boiler to flow 14 gpm if you are only using one boiler.

I agree with Pat.

I had my first Cummins for about 18 years. I only sent it in once for service. They came to my location a couple of times to update the chip for new bills. This spring it went down and I had to send it away 200 miles for repair. They called back and said it was completely worn out and not worth...

Dultmeier has wall mount wringer sink for $394. Hand wringer is $179.

I just found a Costco ad that has a 3 megapixel lorex 8 camera system for $699 if anyone is looking to buy now.

I must be in the minority. All my HP hose is 1/2 inch out to the boom and then reduced to 3/8 or 1/4 inch boom hose. I use reusable fitting from parker all the time. They are a little difficult to install but not all that bad. For the guy wonder about foamy brush hose kinking all the time, try...

Dultmeier sales has 6 different models of a wringer in their catalog

Thanks for the reply. I did figure out how to block certain areas of the picture for motion activation right after posting. I will try your suggestions for zooming. While poking around the internet I found the 16 camera system from Lorex from another vendor for $644 but they were sold out and...

I purchased some of the new HD camera systems along with many others here on the Black Friday sales last year. I bought 2 swann 1080p 8 camera systems from Sam's and 1 Lorex 16 camera capable 1080 HD with 8 ball cameras and 4 motorized varifocus cameras from Lorex. I never did get the 4...

Pallet loads of soap and then add all the little stuff. It all gets shipped free.

The impact pump will use more water vs. the Hi pressure pump unless you have a water recycle system. If you do have a water recycle system the Hi impact pump will work better with recycle water. The rotary pump of the Hi impact is more forgiving with recycled water. I had a company that sells...

I have 5 of the OHD touchless, the first generation of the radius. I have been extremely happy with them. I have had some for over 10 years and they are IMO the most reliable machine out there. THe biggest problem I have seen is that swivels wear out but that happens to any machine. I have the...

In the past I have sprayed some WD40 into the incoming air inlet to free up the piston. The piston has a Teflon type ring that can get gummed up. You may have to take the top of valve off and manually push the piston so you can clean up accumulated gunk that keeps the piston from sliding. It is...

I would also go 12 wide if you can. That being said all my doors are 10 wide. On One end I do go 12 feet high so that the bay can be used for other things in the future if needed.

I had one location that was next to a Cstore. I used the Hamilton Tokenotes with a $1 value that the Cstore would pass out to all of its gas buyers. It worked very well for me. I would get around 10 per day redeeming them. I tried to do it at other locations with nearby C stores . that were not...

It is empty now

Darin, please private message me so I can look at one in Arizona. I have been trying for 3 weeks to get Ryko to tell me where I can see one and no one at the factory would give up the location to my distributor.

I go to the local metal supply outlet. They often have some scrap pieces of grating that you can buy pretty cheap. If not they will cut you some in bigger lengths. I buy some metal cutting blades that I put on my skill saw and cut it to size myself. You can buy a whole sheet and cut it yourself.

I think they are trying to get a few machines out and it is introductory pricing for this new machine.

I am lucky to have RYKOs largest and one of the last independent distributors in my area. I have had the same tech working on my Ryko stuff for over 20 years and he is as good as there is. I have had great service from them. In comparison My quote on the Ryko Soft GLoss machine with similar...