Search results

This is from an old post I made. I am just getting around to converting the LP wax to HP wax. I put in the new solenoids, they are mounted next to the HP soap solenoids, made new manifolds on the suction side of the pump to add the wax hose to it, hooked the in and out lines in reverse so they...

I Concur...

Yes you can get them at shallco.com. http://www.shallco.com/power_switches15.html click the series 16 .pdf file, scroll down and you will see them. Thanks for the input guys! :D

Sorry the correct #'s from KR are: st0216ja -Jumper around st0216jb -Jumper back

They may come with a 3 stack switch but not with the 2. I ordered them from electroswitch, pack of 25 is only like $5. I looked all over there website last night but couldn't find them. I called the # provided but they said it was a different division in MA that had them, so they gave me the...

Do you remember which manufacture? I looked all over electroswitch.com, could not find them. Also, they don't come with the switch I use,which is the Electroswitch 2-stack from KR.

Anyone know where to get these small jumpers for a rotary switch? They are allot easier to use then solderless terminals and wire. The nickel is for size comparison.

Can someone please explain the function's of a GinSan GS-27d Logic Controller.

I'll do that.

I replaced the motor contactor and overload protector with a new one and seem's to have solved the problem. There must have been a problem with the overload protector or the contactor, I am not sure. Checked the amps on each leg and they were within the limits stamped on the nameplate...

I have one that has kicked 2 days in a row. Any suggestions on what to check? Seems it kicks all the 24v, the gs31 display in the bay goes out, yet the gs401 inside still stays on. So I’m not sure if it can be kicked by any short or problem with any of the 24v wiring, or if it is just related...

Use Xylol, Put xylol heavy on a cloth, use a razor blade to scrape off glue, wait about 30 seconds till the glue starts to soften then keep scraping and applying xylol till it is gone, If it is good glue, and is on thick, you may have to take off in layers, but you will be able to get it...

On a Therm-X-Trol ST-12 expansion tank. Installed on the main 2” Incoming line at the Carwash. The incoming pressure is 70psi. Max pressure on st-12 is 150 psi. It Says in the instruction’s to Adjust pre-charge to equal incoming pressure. Would it be correct to pr-charge the expansion...

Are you old enough to remember Alpo Horsemeat in cans on the shelf in the supermarket?

I had this same problem at one of my washes where I had the price at 2$ for 4 min. It was 30 sec per coin, if they inserted 1$ the display would read 2:00, making them think they inserted $2. So I displayed the information below on each changer to try and resolve the problem...

When I was a kid , i picked up a pigeon, didn't hold it for long, when I saw my hand was covered with 100's of little red spider mites, needless to say it freaked me out enough that i never got near a pigeon again.

I tried the IDX x-10's in 3 bays, they were the worst out of the different ones I tried, they rust and corrode terrible, and became unusable after only a couple years, I removed all of them. They are a good acceptor, and I think they would be ok in a vendor or something that is in a dry...

Which model did you use?

Dilling-Harris, purchased in 1995. There are no plugs, everything is wired to a terminal block.

Anyone use a probe style 24v low water cutoff on there boiler for the in bay hot water wash and rinse. Taco makes a couple different model's but I'm not sure which to use. The line on the boiler that the switch is located is 2". I have been using the watts fs-10c paddle type and I can't...