Search results

I've had the cryptopay goldline retrofit on mine for a couple years now. only problem I had was some bad pixels on the included display replacement and it was promptly replaced by cryptopay. Have found Cryptopay support to be good so far. Biggest issue I have is customers swiping card with...

Yes pretty close to the same on both ends now.

As I recall, the only issue we had when we installed the replacement gantry, is when I covered one of the the eyes the first time, it went the wrong way. and as I recall, I switched the wiring on the eyes. I'm now thinking I should have switched the hydraulic lines instead... It does slow down...

It stops on the limit fine and has not jammed against the springs. When I homed it at the weld mark on the rail closest to the enterance, it turns the blasters on while travelling vertically, and off while travelling across the top of the rail. I left it there so it would wash better. When in...

adjusted prox switch on pulse wheel, it was a little off center but very close. No difference. then I re-homed the machine at the weld mark on the other rail closer to the entrance of the wash. rand from there and the blasters came on when they were supposed to. lf it is in fact correct to...

I use that as well as turn off the breaker to the PLC and the machine always homes. It will move home forward 6" or so over 2 or 3 months or so. If it looses count and goes to the prox limit, when it reverses its almost like it thinks it is reversing from home rather than the forward limit. so...

Thanks, I suspected it has something to do with that, to do what it is doing, it seems it would have to loose count traveling in the forward direction only as power blaster is coming one way to early toward the rear. I'll check the clearance. there is a slight bend in the drive shaft due to some...

It has a pulse counter (prox switch counting rotations of the driving shaft). the ends of travel are by prox switch at each end. It seems to me that powering it down completely at home, should reset the count of the position counting swith, its like it wants to start further back, but that...

My 5000 is not turning on the power blasters when it goes down the front (washing the grill of the car). and the side spinners and power blast are coming on 2/3 of the way back rather than as it transitions to the downward slope. Its as if it wants to be homed close to the entrance of the wash...

Yes, a private business can do what they want, Like a baker can choose who he will and will not make wedding cakes for or a restaurant can choose to serve only "certian" types of people.

I think there may be some laws about commercial use of programming. some local buisness had to stop playing the radio over their pa system. maybe sirius is open domain? Or maybe what they don't know cant hurt you....

I believe there is an extra charge, and the cyrptopay readers need the wires on newer units that attach to the coin acceptor. I don't know if it can tell difference between bill acceptor and coins.

fixed it. You can set the pre authorization below your swipe charge limit, but you are at risk.

You can call and adjust the pre authorization amount down. However if using count up and someone goes over the authorization, you are at risk that the charge will be rejected. We lowered our reautherization. actually got a bad google review because someone spent 6.00 in our auto and his debit...

... better than owning a full service restaurant or barber shop!

We operate 2 small SS car washes, one of which also has an IBA. We sell tokens at both. The smaller one takes bills on all the equipment. the larger one requires our custgomers with bills to use the token machine. All machines also take quarters. Even though we don't sell quarters at either...

I have 2 washes, one 3 bay ss and one 4 ss and IBA. I also run a full time business (about 50hrs week). the 3 bay is only a half mile off my daily commute so I can stop by twice a day. No trash cans at this location and seems to be working out OK, have to pick up the "protest" litter once in a...

I put these in instead of the tubular type after I ordered the "tool" to open a bunch of locks at a closed wash I bought the salvage rights on. May not be any better but harder to pick, and the stainless disk the key goes through should make it harder to drill or grind out the guts.

looks like the tubular lock was "picked"

I just installed 3 meter boxes using double medeco T handle.s...sent you a PM