Search results

Nayax offers THIS ADAPTER for hardwired installations. It plugs into the back of the reader and provides an RJ-45 female socket for the Cat5e/Cat6 network cable. Install a network cable from each meter box to an equipment room network switch. The network switch then connects to your DSL/cable modem.

Eric, My library of Raypak manuals has long been discarded. However, here's a copy of a DHW boiler manual from Huron Valley Sales' website. Page 12 outlines the make-up air specifications for similar hydronic boilers. RayPak Manual No by-pass valve? If so, the boiler is "seeing" cold glycol at...

The "root cause" is closed combustion air vents in the equipment room. Or, improper or closed boiler by-pass valve. Or, both! Operators who block the equipment room vents save on heating expenses and eventually pay for it with heavily sooted atmospheric boilers. Closed or Improper by-pass...

You can simplify the system by eliminating the foam generators and metering valves and improve product delivery with a few changes… 1. Air pressure regulators with gauges feed the FloJet and the air-assist solenoids 2. Run 1/4" poly tubing from each pair of solenoids 3. Connect the 2...

Weepmizer is commonly used in cold weather locations. It will save significant water and keeps folks from using the "free water". Leave the default settings alone...it works just fine. With the default 1 minute cycles: AT 34° water will flow for 6 seconds BY 25° water will flow for 30 seconds...

^ This Citing significant increases in expenses for energy, chemicals, parts...Several of my customers have gone to $5 to Start - $1/minute. IMHO...$2.00/3 minutes (22.5₵/min) will allow you to go broker faster. You're not going into the Car Wash business for the fellowship.

Pulse 1 wire must be connected to Dixmor LED6 Pin 8 (White/Black wire) You're welcome (in advance).

I’ve had good luck with the Dyna-Jet wringer. Install it on this Chamois Sink for a complete wall-mount system.

Wow, 2Biz! Your project started in 2011. Time flies. IIRC, my original system was installed in 2003(?). It's still in operation. I believe the PFG system is for elimination of water weep for the high-pressure guns. Our systems are for low pressure foam guns and foam brushes. My 2020 version...

Tip ratios are with 25PSI minimum water pressure and with water-thin viscosity chemicals. Volumetrics or titration will eliminate guesswork. HydroMinder 511 Instruction Sheet

Dixmor remote

Do you mind sharing how you hooked up that external stop button?

HaHaHa. Would you prefer Cat's Pajamas? I’ll just say, The 1st bumper sticker I ever applied....“I LIKE IKE”

My experience with Paraplate CVs is less than steller. They're good, but the brass poppets erode over time and the 2 o-rings tend to harden. The Rego stainless poppets never wear out. I can recall having to replace one spring…many moons ago. The low pressure foam gun conversion is the Bee’s...

We've used Rego's stainless steel CVs, like forever. With several hundred installed, about the only thing that goes wrong is an easily replaced o-ring. Expensive? Yes! But, with many approaching 30 years old, I feel that they're 1st money well spent.

That's my technique. No ball valve adjustment required. 😉

The Laurel 899MAX with Microcoin QL acceptor has been heavily favored and highly regarded by my customer operators who dispense $1 coins only. Laurel’s 399MAX is a steady performer, too. It’s especially popular in the college town locations because there’s no knob to pull or button to push...

Here’s the math: 1 gallon of water will absorb 3 pounds of salt 8 pounds of salt will efficiently regenerate 1 cu ft of new softener resin to approximately 80% capacity (Regenerating to 100% capacity will require ~24 pounds of salt per cu ft…not efficient!) So…a 4 cu ft resin bed will...

Degrease the sheet metal. Most sheet metal rolls have a thin film of oil from the factory…and dirt from the brake. To prevent chemical melting of the poly-iso, use foamboard adhesive like: Loctite PL300 We use a Milwaukee Caulking Gun because our hands cramp badly trying to manually apply the...

A customer shared his frustration with color 1 consumption... “It blows through the pink foam and barely uses the blue. I just use one color now.” Sure enough, his 3 Hydrominders were all supplied from the pink foam jug. “I can fix that for you.” I boldly promised. (I left out the “I Think”...