How are you guys attaching the elbow? Does it have to be welded? Can it be clamped?
Air logic or Air shammee
- Thread starter Hamilton's Car & Dog Wash
- Start date
Mattwash
Member
clamped it then used self tapper to hold in place. Definitely wish I would have extended the books another 2-3 feet.
Kim,
Where did you get the mosmatic swivel for the boom?
Also what size clamps are required for the boom? Automotive clamps don't have as much adjustment as regular clamps. Want to make sure I get the right size.
Where did you get the mosmatic swivel for the boom?
Also what size clamps are required for the boom? Automotive clamps don't have as much adjustment as regular clamps. Want to make sure I get the right size.
Kimberly Berg
Well-known member
Hi Noob, I purchased the Mosmatic boom elbows directly from Kleen-Rite (Part #: BOMP60314). They don't swivel. You'll need to call them for current prices. 1-800-233-3873. Their elbows come with a heavy duty hose clamp, but we still welded the elbow to the Mosmastic 3' extension (Part #BOMP60315). I definitely recommend adding the 3' boom extension! Though it does add weight to the Diskin wall bracket, it takes the pressure off the hose so customers aren't pulling the hose to get it over their cars. As for the weight, we ended up adding brackets, with long screws and drilling them through the thick concrete walls.
Attachments
Kimberly Berg
Well-known member
Yes! That's the Mosmatic 2” in-line swivel coupling. I purchased it also from Kleen-Rite (Part #BOMP60323). It swivels much easier & smoother than a rubber vacuum swivel. Pricey little bugger. I paid $132.27 each 6 years ago.
OurTown
Well-known member
Instructions say about 10 degrees. IIRC I mounted our brackets about 3/4" out of plumb along the sides.
I need some advice. I went mount my booms today and ran into some problems. As you’ll see in the picture my bays aren’t all that tall. I planned on mounting the booms just underneath the top of the HP hose. My problem is that I mounted the boom with about 8 degrees of lean to ensure the boom will return to the wall and in doing so the end of the boom is only about 7- 7.5 ft off of the floor. In my opinion that’s not tall enough. I drive a stock ram 2500 and at current height it will come extremely close to hitting the top of my truck. Here are the options I’ve came up with.
1-don’t use the booms and just use a straight hose.
2-I need someway to raise my HP boom. Not sure there’s an easy way to do that.
What’s your thoughts?
1-don’t use the booms and just use a straight hose.
2-I need someway to raise my HP boom. Not sure there’s an easy way to do that.
What’s your thoughts?
Attachments
edredtop
Well-known member
Go to the top block, use a large backing plate to spread the load. You'll still have room for the flex hose on the top (your plumbing looks great for it). Less tilt (tilt is overrated imho as the long hose tends to stretch over time and drags on the ground preventing complete return anyway.
OurTown
Well-known member
The hose will need to be cut after a while in that height bay. I think we had to cut 3 or 4 feet off ours when we had the short ceilings.
edredtop
Well-known member
I don't think it's really matters if it's above or below the HP boom. I've never seen anybody use the dryer boom from wall to wall. I'd say max is about 135° past it's home position. Most customers figure out the extra hose quickly but there is a small group out there that could get tangled up in a ball of yarn...
A few more things:
If needed, remember you can invert the boom to lower the location of the fasteners and raise the boom. Yeah, it looks a bit messier but if it solves a problem....
Second thing is to take note of how much the inlet on the boom swings, if I remember correctly, it was about 6 or 8" so don't get too close with your PVC or you'll create an issue where the flex hose doesn't allow for the desired movement.
I tried Vern's approach as well and it solved a problem on one of my installations. It took about an inch of shim at the base to get a result.
Putting a small stainless steel washer under the bottom of the boom between the boom and the mount (and then drop the bolt through) so the boom rides on the washer instead of the whole mount seemed to help with reducing the resistance too.
Attachments
