Search results

Any coinbox with relay arming can work with a Softgloss. It really depends on what vintage of machine you have for the steps you will need to take. If you can send me a PM with your serial number and program/rev inside the PLC, I can send you the info you will need to make the transition.

If you replaced your VFD, did you program it? When you manually drive the machine, are you using the enable switch? If it's just not changing directions, I'd suspect that relay K3 may not be functioning correctly as this controls direction. If you didn't program the new VFD, and if the relay...

My 40 gal Bradford White PowerVent was going on 18 years and no issues. Just pulled it and replaced it with a new one when I updated my furnace last year. My vendor was also pushing Rheem, because of his discounts, but he was marking it up more than he did the Bradford White.

Great! I sent you a link to your manuals.

Looks like you have been really good direction above. If you send me a PM with your email address, I can send you a link to the manuals for your machine. From the photos, there are a couple of tags that looks like it says sales order 429306, correct?

That contactor looks like it's in your old OHD TPD control cabinet. If so, that was NCS P/N 10629-269, and it is rated at 37A. We still have that parts available if you need it. Or, if you look on the side of that AB contactor, it should show you the AB part number, then just use Google to...

I agree with Mac to have a drink, but then to hire someone familiar with a SAW to go through it with you. Steve is right that the machine looks like it was installed well and it "looks" like the site was kept up. It's always harder on a machine to be idle than it is if it were running. Once...

The pump stand is Magnum HP. It's not available as a retrokit for older machines. It only works with the SGMX5 with WashBuilder.

Dave, it sounds like your machine got lost because of the vehicle being out of position, and the PLC is expecting different inputs to be on. If it knows it stopped at the rear, and you pushed it home, it is thinking that PLC input X53 (rear endstop) should be on. By pushing it to the front...

I'm not sure what you are asking about a "jog" feature. Your machine does the rear arm oscillation where it allows one arm to move out, while the other moves in. When this happens, it will move forward for a couple of seconds before it backs away and switches to the other arm. You should have...

I haven't seen any issues with the rear arm oscillation hurting the brushes, but I do think it works better when we leave the "extra-high" air off and only use rear high air at the back. That prevents them from pressing too hard on the rear. I like to keep the tip speed of the brush maintained...

Yes, any existing machines could be upgraded to the longer brushes. It's just a matter of replacing those top sections.

Coach, I'd recommend you just have them go through and do a preventative maintenance. Tighten all set screws on all bearings. Grease all bearings. Make sure arm pivots are tight, and arms are levelled properly. Make sure boom is articulating properly, and the gap is good between wall and...

Wire 220 from Y13 should go to a terminal strip, then branch out to the contacts of K61 and valve Y8 (cooling valve). If you remove that cooling valve wire, I'd recommend you jack up each corner of the machine, and remove the idler wheel to clean and put a light coating of fresh grease inside...

It does sound like the PLC relay for Y13 is likely shorted on if that contactor K61 is pulling in. Before you replace your PLC or get this one repaired, I'd recommend you have someone that has an HPP programming console write down how all of your setup questions and your D timers are currently...

Coach, in mid-2019, we implemented a change to the upper sections of the rear arm brushes to help improve wash quality on SUV's with their increased angle of the rear glass. The upper 7 sections are now using 72" length brushes rather than the original 60". This has made a big improvement I...

On a Monarch II, the code 12 indicates a problem with the tire finder photoeye not transitioning. These are the photoeyes mounted along the bottom rail of the machine. PLC input X35 should be "ON" when unblocked, and go "OFF" when blocked.

PM sent with the manuals

I can't order the parts for you, but after I send you the manual, you can either call 800-283-7956 to order the parts, or you could send an email to partsorderentry@ncswash.com, and they can assist you. We've expanded our online parts website, and you could also order through there. Here is a...

Service/Parts Manuals for those are site specific. If you can get me the serial number of your machine, I can probably send it to you.