Search results

I rewire the solenoid manifolds which are powered via a PLC. The air solenoids on the PS panel provides air for all low pressure products...eliminating the need for air solenoids for all other LP gun products. The PS air solenoids also provide the blowout for freeze protection. But again, the...

Kwoelke, The Foaming Gun system can dispense any number of low pressure products. Most of my customers have Tire Cleaner and Presoak on the foaming gun. One of my customers provides Tire Cleaner, Pre-Soak, Bug Cleaner, and Mag Chloride Cleaner from the foam gun. In every case, the high...

Based on the labeling, the media tank appears to be an uncommon size - 21” diameter x 54” height. Pentair’s Structural USA brand 21” diameter media tanks are available in heights of 36” and 62”. Clack’s 21” media tanks are 62” tall. Therefore, replacing the tank will require an ~8” longer...

Change "OFF" to "STOP" Swap Tire Cleaner and Pre-Soak positions Swap Rinse and Foam Brush positions

Looks like you found THE water softener forum . You'll get expert advice from "Bannerman" and "dittohead". For Pentair parts and equipment, "dittohead" will likely hook you up with a dealer in your area. FWIW, 20 year old resin is likely at end-of-life...especially if it's treating chlorinated...

Mac, If you are a Comcast customer you can obtain an Apple iPhone SE for free from Xfinity Mobile. When I travelled the country for work, AT&T provided nationwide coverage at a reasonable(?) price...the company paid the bill. After retirement, I discovered I was paying through the nose for...

If your facility has a landline, this device can dial several numbers I've used them to report bill changers out of service, excessive noise in the equipment room, low temperature, etc. https://www.sensaphone.com/products/sensaphone-400-and-800-monitoring-systems I have no experience with this...

I would recommend having the Rowe coin dispenser overhauled by a reliable service provider. There are two providers in my region with which I have had great success. You may find similar service providers in your area. IMHO…Based on prices and availability of Rowe machines and parts, it appears...

It's an RO production unit and a repressurization pumping station from https://www.huronvalleysales.com/spot-free-rinse.html SYNCRO (So You Need Cheap Reverse Osmosis) :LOL:

Read the "Tech Tip" on page 13 https://www.catpumps.com/sites/default/files/2019-12/993330E%20GUD%20System%20Design.pdf

Softener went into regeneration. Step 1: Backwash - Valve opens to drain and flows at close to city water pressure. Step 2: Brine Draw/Slow Rinse - Valve opens to slowly draw brine at reduced pressure. Typically, brine draw setting is 1 hour. Brine tank empties in 15 to 20 minutes and then city...

I’ve been converting my customer’s troublesome float valves with the Hudson Valve. Some installations require fabricating the inlet plumbing to properly locate the valve inside the tank. Open tanks can be installed using Hudson's Mounting Bracket

I’ve become a big fan of Ginsan...They are great to work with. I have them equipped with ElectroSwitch 10 position rotary switches for reliability and easy/inexpensive replacement. Add a seal nut: N9060X1/4 2 APM Hexseal | Switches | DigiKey and a glob of silicone grease to the stem to prevent...

If flowing pressure drops below 25 PSI, the Hydrominder will not draw chemical as expected. Snipped from the Hydro Systems instruction manual: “Minimum water pressure required to properly operate the proportioner is 25 PSI (flowing).” Observe the Hydrominder’s operation while the rinse water...

Start with 40psi pump & 30psi air. Add 1-2psi air for dryer foam...subtract for wetter foam.

Operating with a 10psi liquid/air differential, I've never found it necessary to install check valves on the air lines.

I like these https://www.kleen-ritecorp.com/p-2019-hudson-float-valves-high-temperature-1.aspx

Randy's on to something. Several of my clients have timed output from the bay timer powering the coil of a relay...whose contacts supply power to the motor starter coil. This is because there is significant voltage drop from their coin box to their pumping station's electrical panel. (due to...

I PMed a contact name/number to tbone. I was just sharing my experience... in case someone reading this thread was considering updating/replacing a BC-1400. (You know how these threads go off the rails, right?) :ROFLMAO:

I recently replaced a beat-to-death BC-1400 with a Standard MC400RL-SLIM for a client. They're quite pleased with it...and so am I...my frequent service calls for this site have been dramatically reduced.;) https://www.standardchange.com/PDFs/MC400RL-SLIM%20BrochureA.pdf