Search results

That’s my experience. Pump pressure helps, too.

The key to rapid product changeover is to run all product lines into a manifold, directly above the foam gun’s boom. Since the individual product lines are always full, changeover time is reduced to 5 seconds or less.

Noob, 3 product lines, 1 air line, 1 anti-freeze line are connected to a manifold above each bay (Inside an insulated plumbing trough) A single 3/8” poly tube exits the trough and connects to the wall mounted coupling. Because the system features freeze protection, I can mount a foam generator...

https://www.kleen-ritecorp.com/p-44523-stainless-steel-triple-foam-wall-mount-holder.aspx I use these for every foam gun conversion/installation...over 100 bays, so far...along with Freelin-Wade coiled hoses and Hamel non-trigger guns. The most recent install features PS, tire, Mag chloride...

I have no experience with this. You can likely do what you want with some of these devices. https://www.controlbyweb.com/

https://www.kleintools.com/catalog/cable-tools/ratcheting-cable-crimper-stripper-cutter-pass-thru I never look forward to building network cables. Until now. These pass-through RJ45 plugs almost make it fun, with little chance of a miswire or short. I‘m not affiliated with Klein Tools...just a...

I suspect there are local suppliers in the Dayton Metro. Search for "Automation", Fluid Power, Pneumatics. In a pinch, HD sells Watts AquaLock fittings...$$$

KQ2 https://www.smcusa.com/products/connectors/fittings/one-touch-fittings/kq2/North-American-Inch-New-Series~87053

Been using SMC and Pisco fitting for every job for over a decade. https://www.pisco.com/products/Standard_Pneumatic_Tube_Fittings

Official Colorado snow depth measuring device(s). The all time record at my house is 2 Six Packs

Low level of product Shampoo tank low level float switch Poor connection LLFS to Timer Faulty timer (8 pin harness - pin #6)

Yeah, I used 6lbs for years with Bruner softeners. However, as time goes by I've found capacity reductions resulting in hardness leakage. I decided to quit picking nits and just go with 8 lbs.

Greg, Maybe this link will help. A bit tech heavy but it does a good job of explaining. Basically, it comes down to doing "the math"...something the electronic timer/controllers will do for you (if it's programmed properly). Some key numbers: 8 lbs of salt per CuFt of resin 1 gal of water will...

Many moons ago I ran Low PH foam brush until I realized the exposed aggregate path from the brush to the floor drain was rapidly enhanced! It did a great job on windshield eyebrows and chrome.

Greg, My fav was Bruner with IQS-3 controllers. They were awesome...easy to maintain, service, and set up. I've never had to repair a Clack valve. Mainly because there are very few in my area. I like Pentair 9500 Twin Alternating with the SXT controller for smaller facilities (up to 21GPM...

I work on a variety of systems...Livingston, Mark VII, Southern Pride, Coleman, Hydrospray, HPWS. Most softeners are equipped with Pentair (Fleck) valves...some Clack...and a couple of Bruners that are just barely alive.

Most munis and Colorado’s DOT apply brine mixtures that often include Mag Chloride. It’s difficult to remove so many operators have a “seasonal” selection on the dial... Mag Chloride Remover in the winter, Bug Remover for the rest of the year. Some just swap out PreSoak for Mag...

At 1,000 PSI: #6 spray tip flows 3.0 GPM #7 spray tip flows 3.5 GPM At 1,200 PSI: #6 spray tip flows 3.3 GPM #7 spray tip flows 3.8 GPM

Roz, Unfortunately, those solenoids are "legacy" products from SMC. https://www.smcworld.com/discon/en/oldpdf/VX2-old-e.pdf

Might have something to do with transportation/fuel cost? Diamond Crystal: HD in Birmingham $6.47/bag HD in Salt Lake City $4.97/bag HD in Denver $4.47/bag