Search results

Have you tried calling the phone number displayed on the decal?

That era of Hydrospay equipment utilized the booster pump for circulating heated pre-soak to the roof-top plumbing trough. Each bay’s PS solenoid was teed in the circulating loop, above the bay. The concept is to use the heated PS to keep the trough warm. It’s a pain-in-the-neck to...

Adding to Greg Pack's excellent advice... With all products being dispensed through a foam gun… Ensure your chemical blender (Hydrominder?) is functioning properly. Clean or replace the metering tip…make sure the Hydrominder discharge tube restrictor is in place. Sputtering products might...

You mean like this? :geek:

Beyond fulfilling the developer’s dreams, the PLC: Inputs can be on/off time delayed. Provide outputs to multiple devices (solenoids/motor starters/water heaters, temperature-controlled circulating pumps, weep systems, etc.) Provides operator settings for price-to-start & bay timing. The coin...

"AFAIK, Modicon is no longer in business." Correction...Modicon PLC is still in production.

The HS hardware is quality stuff. Just be aware of the potential PLC concerns. The Modicon PLC program was written during HydroSpray's Precision Auto ownership...in the 1990s. AFAIK, Modicon is no longer in business. And, those old HS smart guys are long gone. I'd be surprised if the 4th...

Several hundred bays here... Orange = 24 hot Green = 24 common

HA! Virtually every customer of mine has the “glazed eye” condition. My service calls would likely be halved if there were corrective lenses or medication.

That's the story. Might have something to do with the CryptoPay/Dixmor relationship? (Rumor and innuendo mode OFF) Too bad, because I like the LED6 display better.

Turn on a non-soaping bay. Place the tip of a pocket screwdriver on top of that bay's soap solenoid. If it feels magnetized the electrical circuit is functioning properly. If it doesn't, you have an open circuit...most likely the 24v commons for those 4 bays have become disconnected.

Correct info Keno. Prior to the "redesign", Dixmor LED6 was the easiest way to install Nayax... Nayax Pulse wire 1 to LED6 Pin 8 (White/Black wire). Boom, Done! On the Dixmor LED7... Pulse wire 1 to LED7 Pin 9 (White/Black). Same Boom, Done! No interface Opto-coupler relay required.

That's correct...in theory. Old Guy Side Note: Decades ago, those newfangled digital display coinbox timers used a board-mounted battery to maintain the programmed settings memory. If the timer's battery was dead and the car wash experienced a power outage...well, timer settings reprogramming...

Here's a possible anti-confusion solution: The HiLetgo 5-volt module features double throw relay contacts. Power the LED6 (Orange wire) thru the relay’s N/C contact. When Nayax activates, the relay switches to the N/O contact and power is removed from the LED6. When credit card is stopped or...

You can by-pass any coin box timer and just let the Nayax provide the power to run the bay. It will display count-up time and money spent. See my informative post here. :LOL:

Yeah, it's appears to be similar to Pro Equipment's Navigator Touch Screen. Especially if there's an Omron PLC in the cabinet.

It snowed 10-12” over the weekend with temperatures dropping into the low teens. Monday, the clouds broke, the sun appeared, the streets cleared with sub 30F temp. (We’re closer to the sun here… donchaknow?) The queues were 3-5 cars deep at most of the coin-ops. “You should start taking...

I don't have a problem calling them...because I quit trying. I did a ton of business with them over the past decades. Times have changed.

Noob, I'm not comfortable giving electrical advise to self-proclaimed electrical idiots. LOL! After re-reading your thread starting inquiry, disregard all my excessive instructions. Your existing or newly purchased float switch will work. Just cut the electrical plug off and connect it's 2...

Using an Omron LY2N24VAC DPDT relay From your car wash’s transformer: 24v Hot to one wire from both float switches 24v Neutral to Relay’s coil (Omron terminal 8) On the relay: Low level float switch’s other wire connects to relay coil (terminal 7) High level float switch’s other wire...