Search results

There is a possibility that one of your wax solenoids is slowly leaking internally, allowing wax to flow back up the soap line from the pump and mix with the soap. This occurs when the pump is idle for several hours...like overnight for example...especially if the liquid levels in the soap and...

Each section is 22 Ga., 10’ long 5.5” x 8.5” with a 1” lip Figure around $80-$90 per 10’ section (2 pieces) for the steel. Plus, insulation, glue, screws, strut, cushion clamps, nipples, couplings, hole saws, etc. Look closely at the pics and you’ll notice the top and bottom are identical...

I typically use Output 2 on a Dixmor Weepmizer to power a 120vac relay...which in turn energizes an outlet mounted under the equipment room ceiling.

Yeah, we have it formed by a local sheet metal shop and add the Formular PolyIso. And, we don’t “dump“ the stuff into it. 😂

Here’s another way... an insulated metal trough on TOP of the roof.

Your municipality may have specific requirements and suggestions. Search online for Sand/Oil Separators or Precast Concrete suppliers in your area.

Be aware of EBay MicroCoin QLs. The QL is also used in the casino and vending markets with different specs and pre-programmed acceptance. All QLs are 12vdc powered. QLs for the car wash industry are supplied with the power inverter allowing 24vac operation. Additionally, QLs utilize a specific...

Well... You have obsolete electronics from IDX. They've been discontinued for several years. New Dixmor LED6 or LED7 coin box timers cost less than $250 each. Everything is one box...timer and display. The Dixmor remote is less than $60. The Southern Pride pumping station should provide another...

Hydrospray’s website states they have Turbo Wash stuff. https://www.hydrospray.com/product/15399

If memory serves, JCC used Omron Programmable Logic Relays with the outputs powering ice cube relays for the motor contactor. The PLR might be "mentally" locked up. Try cycling power to the PLR.

mjwalsh, The Fleck controller is not affected by the condition of the resin...but, you probably already know that. The controller uses timed sequences for each regeneration cycle. Typically: 10 minutes backwash 60 minutes brine draw and flush ?? minutes brine refill (Brine refill time is a...

As water flows through the resin in a funnel shape...sort of like a tornado. The middle depletes faster than the sides. Low flow rates increase the depletion sooner than higher rates. Many modern electronic controllers provide a maximum days between regen setting to prevent breakthrough or...

In addition to chlorine, (which breaks down the divinylbenzine glue that holds resin beads together) oversalting and excessive fast flushing will cause the resin to swell and crack...down the drain they go! Surprisingly, at least to me, was the site where heavy water hammer conditions went...

24”x72” mineral tanks ... 10.6 cu ft of resin each ... 318,000 grain capacity each. Those are huge softeners for a self serve wash. With 15% reserve capacity, 10 gpg hardness and minimum salting, each tank can treat over 26,000 gallons. Unless the wash uses 2,000 gpd, I’d be concerned about...

See? I told you 2Biz would come thru.;)

In addition to OurTown’s comment: If your raw water is 3-5 grains per gallon, you should consider installing a softener. You‘ll improve the wash quality and reduce soap consumption. If you have a softener, you need to fix it. A properly operating softener should provide 0 grain hardness water...

The water supply to the pumps. Mark VII used 3/4" hose to feed the pumps. That size provides more than enough water...preventing soap and wax suction. Every Mark VII system I've ever worked on required throttling the water supply with the ball valves... That is, until I replumbed the pump...

That’s always been an issue with Mark VII Proline. Follow MEP’s advice or re-plumb the pump inlets with 1/2” hose.

Found one pic...from 5 years ago.