Search results

That valve is a Lexair 334524V. We do have a poppet repair kit P/N 18318-805 if that helps. It includes the poppet o-ring, and a teflon wear ring.

Fia29 was purchased and later closed. Several of those that used to work for Fia29 (or Ryko Italia) now have their own compeny called Croma Service. For support, please send an email to service@croma-croma.com and they should be able to help you.

Usually, the high voltage fault code occurs when there is a fault with the VFD. I would recommend you turn off the 3 phase power to the machine, open the main control panel and inspect for any loose wiring coming from the disconnect and going over to the VFD as well as all the contactors and...

Ryko has the HPP available, but if you are able to find them online, please use a little caution. The ones we use do have proprietary software installed to bring up the various screens used in troubleshooting. In other words, it allows you to pull up the setups, diagnostics, etc. If you use...

This may vary by vintage of machine, but most machines are 1" for both the wash water and rinse water. An RO valve is 3/4".

The main wash water valve should be a 1" valve. It is more likely that the coil has failed rather than the valve though. The coil would likely be pulling down the voltage until the CB trips in the case of what Steve is seeing.

Steve, CB1 controls wire 11 which supplies +24VAC to the bank of inputs Y20 - Y37. If that is tripping, I would suspect one of the water valve coils may be shorting. Most likely, it would be either the wash water valve on Y30, or the rinse manifold on Y31. Based on what you described, it's...

SuperClean, if you are using Ryko activation and have a CAW, you can go into the reports and pull diagnostics. If not, you would need the HPP. Brushes should not turn on in first pass from front to rear, but they should turn on from rear to front. If the front arms don't come in on the sides...

Do you have a CAW on site? If so, please go into reports and pull up diagnostics history and send it to me. It sounds as if your machine is tagging on of the 8XXX or 9XXX codes that indicates it is shutting down. With this, I should be able to give you some guidance on where to look...

When this happens, is the machine already stopped at the front spinning the brushes and moving the wiper? It sounds like at the point this is happening, you have something pulling down the 24VAC so it can't drive the outputs. Try monitoring wires 25 and 26. You should have 24VAC plus/minus...

Steve, this is off-topic for this thread, but if you look across all the different manufacturer platforms, there is a wide variety of boom designs being used. Several are using an articulated boom design, while others are using the caterpillar E-chains or taglines. Each method will have...

If you look in the machines diagnostics history, it should give you a good idea of what happened. The diagnostics history provides not only the diagnostic 4 digit code, but also the sequence code information to let you know what part of the cycle the machine was in when that code occurred. You...

Airswitch for activating fixed undercar. They could use either an airswitch or photoeye.

The output signals from the ultrasonics is not a steady state, so it's normal if you are watching the input on the PLC for the LED to flicker. If you are having issues where it's not properly locating the rear of the vehicle, you would need to monitor D25, and ensure the value falls within how...

RykoPro is our Service Manager for the Michigan and Ohio territories and I'm working with him all the time. He probably just doesn't have as much time as he used to on the forums.

This machine was originally ordered with the wax option rather than the clearcoat option which explains why it's wired that way. There isn't an adjustable timer that I can see for the prime time on the wax function, but there may be a data register that I could change that may help. If you can...

Can you tell me what program and revision you are running in the OHD? It should be a number like 23953-00X or 26234-00X with a letter revision after it. If you have the serial number of the machine and the output you are using for the Clearcoat, that will help me to answer your questions.

PM your email to me, and I can send it to you.

CAW iC Administrator Password For sites that process CC through a CAW iC, either the site operator manages the password, or they are maintained and changed every 90 days. I sent you a PM so you can discuss with others from my team to help you with what you are working on.

Brian, I'll have someone contact you shortly. I'm sorry for the difficulty!